Polar Cloud Knowledge Base

FAQ 9

• Part doesn't stick to the build plate
• How do I get a quote?
• I think the part is too big for the build plate
• What kind of filament can I use?
• What is the average length of filament in a 1 Kg spool?

See all 9 articles

Warranty & Safety Docs 3

• Polar PLA Material Safety Data Sheets (MSDS)
• Polar Care & LTD Warranty
• Other Safety Reports

Getting Started 6

• When do I need to use support material in my prints?
• Applying Hairspray to the Build Plate
• What is the correct distance from the nozzle to the bed for my 3D printer?
• What is infill?
• Where can I learn about basic 3D Printing/Slicing terminology and see examples?

See all 6 articles

Polar Cloud 6

• Polar Cloud Introduction - Overview and Walkthrough
• Adding New Users or Managers to Your Cloud Enabled Printer
• Joining a Group on the Polar Cloud - Join Code
• Creating and Utilizing Class Groups on the Polar Cloud
• How Do I Adjust the Strength and Resolution of my Prints?

See all 6 articles

Network Requirements & Basics 1

• 3D turns and stays yellow?

Dremel 3D45 8

• Dremel 3D45 - Owners Manual
• Getting Started
• How to Add your Dremel Digilab 3D45 to the Polar Cloud
• How do I prep and maintain my Dremel's build plate?
• How do I remove my Dremel's build plate?

See all 8 articles

Flashforge Inventor II & Inventor IIS 16

• How do I add my Inventor II or IIS to the Cloud?
• How to Update the Firmware on your Inventor II or Inventor IIS
• I just got my Inventor. How do I get started? (unboxing, loading, leveling)
• Flashforge Build Plate "Leveling" - Never Reaches Probe
• How to Use Ethernet with your Inventor II

See all 16 articles

Flashforge Finder 2

• Does my Finder work with the Polar Cloud?
• Can I use a camera with my Finder?

Flashforge Guider II & Guider IIS 1

• Working with your Guider II or IIS

Other (Octoprint) 1

• How to put (mostly) any 3D Printer on the Polar Cloud

Polar3D - General (applicable to all models) 5

• Reading the Calibration Key
• How to Update Your Polar 3D Printer
• How to Read A Calibration Key
• Printing over USB with Polar Printers
• Connecting your Polar3D to your WiFi Network

Polar3D Hardware: P3D00000 - P3D01999 8

• Replacing the Feed Block
• Replacing the SD Card
• Replacing the Fan in the Back of the Printer
• Camera Replacement
• Broken Z-Tube Replacement Guide

See all 8 articles

Polar3D Hardware: P3D02000 - P3D02150 5

• Removing and Replacing the Feed Block
• Broken Z-Tube Replacement Guide
• Loading and Unloading Filament
• Getting Started V2 - Initial Setup of the Polar 3D Printer (Serial number P3D02000 and Above)
• How to Reset Networks?

Polar3D Hardware: P3D02150 and Higher 7

• Broken Z-Tube Replacement Guide
• Loading and Unloading Filament
• REPAIR - Bad Z Mosfet in Printrboard - M119 Will Not Trigger
• Z Homing Issues - Testing the Z Endstop Board
• Loading and Unloading Filament

See all 7 articles

STEAMtrax 2

• How do I order my Perishable components for STEAMtrax kits?
• Introduction to BlocksCAD

Makers Empire 1

• Makers Empire Help Center

Tinkercad 2

• Can I send objects from Tinkercad directly to the Polar Cloud?
• Designing 3D objects on Tinkercad

Training Videos 1

• Polar3D Printer - Unboxing and Introduction

Communication 1

• Welcome to the GE Additive Education Program